RUNS THE TRUNK FILE COMPILER
(SHOULD BE RUN ONLY AFTER RUNNING 'CIP'
- TYPE 'HELP DATABASES' FOR A EXPLA-
NATION OF THIS FILE)
'RUN CODUMP' RUNS THE UTILITY WHICH
DUMPS COI(CENTRAL OFFICE INFORMATION)TO
THE SYSTEM LINE PRINTER
'RUN RTGDDMP' RUNS THE UTILITY WHICH
DUMPS THE ROUTINE TEST FILES TO THE
SYSTEM LINE PRINTER
'RUN DOWN' RUNS THE PROGRAM WHICH SHUTS
DOWN RAMPART APPLICATIONS PROGRAMS IN
AN ORDERLY FASHION. (DO NOT USE THIS
IT IS TO YOUR ADVNTAGE NOT TO FOR IT
WILL NOT ALLOW YOU TO USE ANY
CMDS.)
->REFERRAL NUMBERS
REFERRAL NUMBERS ENABLE THE USER TO
QUICKLY SPECIFY A SINGLE TRUNK GROUP IN
THE SYSTEM BY ITS NUMERIC REFERRANCE.
FOR EXAMPLE, THE TRUNK GROUP 'TG123'
FROM OFFICE 'ABC' TO OFFICE 'XYZ' CAN
BE SPECIFIED BY A SINGLE NUMBER IN
RAMPART COMMANDS RATHER THAN ENTERING
THE NEAREND,FAREND, AND GROUP ID IN
THIER ENTIRETY.
NOTE: THE REFERRAL NUMBER FOR A PART-
ICULAR TRUNK GROUP MAY CHANGE IF THE DATABASE IS RE-COMPILED.
FORMAT: REF-ERRAL NUMBER
RF NUMBER
THE EASIEST WAS TO DETERMINE THE REFER-
RAL NUMBER OF A TRUNK GROUP IS TO USE
THE 'DISPLAY TRUNK' COMMAND.
->DISPLAY TRUNK
DISPLAY TRUNK(GROUPS) NEAREND
OR DISPLAY TRUNK (GROUP)
REFERRAL NUMBER
DISPLAYS DATABASE INFORMATION ON THE
TRUNK GROUP(S) SPECIFIED. INCLUDED IS
REFERRAL NUMBER, NEAREND, FAREND,
GROUP ID, NUMBER OF TRUNKS, SYSTEM
TRUNK NUMBERS, AND LIMITS DATA.
O IF ONLY 'NEAREND' IS SPECIFIED, ALL
TRUNK GROUPS ORIGINATING FROM THE
OFFICE SPECIFIED ARE DISPLAYED
O IF 'NEAREND' AND 'FAREND' ARE
SPECIFIED, ALL GROUPS BETWEEN THESE
TWO OFFICES ARE DISPLAYED
O SPECIFYING 'NEAREND', 'FAREND', AND
'GROUP^ID',OR SPECIFYING THE REFERAL
NUMBER UNIQUELY DESCRIBES A SINGLE
TRUNK GROUP.
->TRUNK
TRUNK NUMBERS
RAMPART USES TWO DIFFERENT TRUNK
NUMBERING SYSTEMS; NAMELY, USER TRUNK
NUMBERS AND SYSTEM TRUNK NUMBERS. USER
TRUNK NUMBERS ALWAYS START AT ONE, AND
END AT THE NUMBER OF TRUNKS IN THE
GROUP. SYSTEM TRUNK NUMBERS ARE THE
NUMBERS USED TO ACCESS TRUNKS ON THE
SWITCH AND MAY RANGE FROM 0 TO 65000.
FOR COMMANDS WHICH REQUIRE TRUNK
NUMBERS,THE '/SY' SWITCH SHOULD BE
ADDED TO THE COMMAND LINE WHEN REFER-
ENCING SYSTEM TRUNK NUMBERS.
->DATABASE
RAMPART DATABASE OVERVIEW
THE RAMPART USER DATABASE IS COMPRISED
OF THE FOLLOWING TWO FILES:
(1) CENTR. OFFICE DESCRIPTOR(COD) FILE-
THE EQUIPMENT LOCATED IN THE CENTRAL
OFFICE KNOWN TO THE SYSTEM. IT CONTAINS
SUCH INFO. AS COMMON LANGAUGE CODES,
LITERAL CENTRAL OFFICE NAMES, ROTL TYPE
AND ACCESS NUMBER, TESTLINE TYPES AND
ACCESS NUMBERS,ECT.
(2) TRUNK SOURCE FILE- THIS FILE
DESCRIBES THE TRUNKS LINKING IN
THE FILE. IT CONTAINS SUCH INFO AS
TRUNK GROUP ID, NUMBER OF TRUNKS IN
GROUP, LIMITS DATA, TRANSMIT LEVEL,
SIGNALLING,ROUTINE TEST INTERVAL,ECT.
THESE FILES CAN BE UPDATED BY THE USER
SOURCE EDITOR (USE) PROGRAM (INVOKED BY
THE CMDS 'EDIT' & 'RUN USE').
[DATABASE SUB-CMDS]
EXAMPLE
COD CEN-TRAL^OFFICE
TRUNK
->DATABASE COD
THIS FILE CONTAINS INFORMATION ON THE
EQPT. LOCATED IN KNOWN TO RAMPRT.
FOR DETAILED INFORMATION ON ITS CONT.,
RUN THE USER SOURCE EDITOR,SPECIFY COD
FILE EDIT, INVOKE CHANGE MODE ON AN
EXSISTING CENTRAL OFFICE RECORD, AND
USE THE HELP FACILITY BUILT INTO THE
EDITOR.
DATABASE EXAMPLE
----------------
,-------------------,
, #3 EAX ROTL ,
, (TEST PORT ACCESS ,
, NUMBER = 5551234),
-------------------
:
:
: :::::::::::::
:::::::::105 RESPONDER:
:::::::::::::
->CHECK
THIS COMMAND CAUSES A RAMPART TEST PORT
TO TO INITIATE A SELFCHECK SEQUENCE AND
RETURN THE SELFCHECK DISPOSITION TO THE
REQUESTING TERMINAL.
FORMAT: CHECK PORT # (OR ALL).
->EDIT
INVOKES THE USER SOURCE FILE EDITOR
PROGRAM WHICH IS USED TO UPDATE THE
RAMPART DATA BASE. THIS PRG. HAS ITS
OWN HELP FACILITY.
FOR INFO. ON THE RAMPART DATABASE IN
GENERAL, TYPE 'HELP DATABASE'.
EXPLANATION OF THE CONTENTS OF THIS
FILE)
'RUN TAC'